|
|
This chapter describes the activities associated with initial startup of a Cisco protocol translator. In general, startup involves some rudimentary configuration of addresses, names, passwords, and other common system parameters.
The following information is included:
The setup command facility enables you, the network administrator, to start using your Cisco network server quickly and without extensive background knowledge. It does this by prompting you for the information required to perform basic configuration procedures. The setup command facility is available on all Cisco routers, terminal servers, and protocol translators with Release 8.2 or later software.
Use the setup facility both at initial configuring of the system and for basic changes at any time. In addition, the facility itself is a teaching tool that aids in familiarizing you with the expected command sequence as you step through the process. Because of these unique characteristics, Cisco refers to setup as a command facility rather than simply as a command.
You can use the setup command facility to configure system-wide (global) and interface-specific characteristics. The configuration activities associated with the setup process are outlined below:
Global configuration activities available with setup:
Interface-specific configuration activities handled with setup:
For more advanced applications, you must enter a privileged level configuration session.
The setup command facility operates automatically the first time you power up your network server. To use setup on subsequent occasions, you must invoke it as you would any other command, by typing it at the EXEC, privileged level, prompt (#). Your system will also automatically run the setup program when it cannot find its configuration in memory.
Before you start using the setup command facility, you need to do the following:
Step 1: Attach an RS-232 ASCII terminal to the system console port located at the rear of the Cisco server.
Refer to the relevant Cisco Hardware Installation and Reference publication for details about cabling considerations and establishing electrical connections.
Step 2: Configure the terminal to operate at: 9600 baud, 8 data bits, no parity, 2 stop bits.
Step 3: Power up the protocol translator (the setup program runs automatically for initial startup).
The server will prompt you for specific parameters including network numbers, IP addresses, and subnet masks, when applicable.
At any time during use of the setup command facility, you may request help by typing a question mark ("?") at a given prompt. If the prompt requires a "yes" or "no" answer, no further help is available. However, if the prompt offers a range of acceptable answers, the help facility will give you some guidance. For example, if you are prompted to select the number of bits in a subnet mask, the help facility might inform you that you can choose a decimal number between 0 and 16.
For many of the prompts, default answers appear in square brackets following the question. These defaults are used when you answer the question by pressing the Return key. If the system was previously configured, the defaults that appear are the currently configured values. If this is the first time the system has been configured, the factory defaults are provided. If there is no factory default, as in the case of passwords, nothing is displayed after the question. In the descriptions that follow, the factory defaults are shown.
The setup command knows what kind of network interface is installed and prompts for configuration information as appropriate.
When you first power up your console and network server, a script similar to the following will appear on the screen. The first section of the script displays the banner information, including the software version (CPT example):
PT Software (PT3-L), Version 8.3 Copyright (c) 1986-1991 by Cisco Systems, Inc. Compiled Fri 14-Jun-91 11:21
The next portion of the display is a list of the installed hardware and software options. By reading the installed hardware, the system automatically presents the appropriate interfaces during the configuration process.
CSC3 (68020) processor with 4096K bytes of memory. 1 MCI Controller 1 Ethernet/IEEE 802.3 interface. 1 Serial network interface. 32K bytes of non-volatile configuration memory.
The Configuring the System Dialog message and configuration steps automatically appear next, offering the prompts for which you'll provide the answers to configure your system. Press the Return key to accept the default settings (if any are available). The Configuring the System Dialog message provides the following initial information:
-- Configuring the System Dialog --
At any point you may enter a question mark '?' for help.
Refer to the 'Getting Started' Guide for additional help.
Default settings are in square brackets '[ ]'.
Continue with configuration dialog? [yes]:
Press the Return key to continue with the setup process; enter "no" to terminate the process at this point.
The remainder of the script is the actual configuration process, with each prompt appearing automatically. The following discussion outlines each prompt provided during the setup process. A complete setup script is provided at the end of this chapter.
Configuration using the setup command facility is a two-step process:
Step 1: During the first step, you specify information on a global, or system-wide basis.
Step 2: The second step allows you to configure the network interface, based on the global information provided previously.
The step-by-step discussions that follow briefly define the global and interface parameters that can be set using the setup command facility.
The following configuration steps pertain to initial configuration for all protocol translators. However, the setup command facility for IGS systems that include the protocol translation option also provides initial configuration for the routing and bridging functions of those products.
To build configurations that provide more sophisticated translation capabilities, refer to the configuration techniques described in the chapter, "Configuring the System," the protocol-specific chapters, and in the chapter, "Configuring Translation."
The following global configuration activities are handled via the setup command facility for a protocol translator:
Each step in the global configuration setup process is described sequentially in the descriptions that follow.
Specify the name of the host computer for the network server. This host name is used in the system prompts. You must enter a host name in order to continue.
Help: Type a string, then press Return. A host name can consist of from 1 to 80 alphanumeric characters and is case-sensitive.
Your system has two levels of security: user and privileged. The commands available at the user-level are a subset of those available at the privileged level. Because many of the privileged commands are used to set operating parameters, they are password-protected to prevent unauthorized use. This is accomplished by setting up an enable password.
An enable password allows a user access to the privileged command level. The password is case-sensitive. You must enter an enable password in order to continue.
Default: Blank initially
Help: Type a string, then press Return. An entry must be made in order to continue with configuration.
An enable password can consist of from 1 to 80 upper-and lower-case alphanumeric characters; a number cannot be the first character. Spaces are also valid password characters; for example, "two words" is a valid password. For more information, refer to the chapter, "Using the Protocol Translator."
In addition to the enable password, each virtual terminal line may also have an individual password. By default, virtual terminals require a password. If you do not set a password, the system will respond to attempted connections by displaying an error message and closing the connection. Virtual terminals are used when remotely accessing the protocol translator via the network.
The virtual terminal password is case-sensitive. If desired, you can allow line connections without a password. Refer to "Establishing Line Passwords" in this manual for more information.
Default: Blank initially
Help: Type a string, then press Return.
A virtual terminal password can consist of from 1 to 80 upper-and lower-case alphanumeric characters; a number cannot be the first character. Spaces are also valid password characters; for example, "two words" is a valid password.
The Simple Network Management Protocol (SNMP) is the most widely supported open standard for network management. It provides a means to access and set configuration and runtime parameters of the routers and terminal servers. SNMP defines a set of functions that may be used to monitor and control network elements. Answer "yes" to configure SNMP on a system-wide basis. Refer to "Configuring Simple Network Management Protocol" in the chapter "Configuring the System," for details about specific SNMP parameters.
Answer "no" if you do not want to run SNMP.
Default: Yes
Cisco supports the Network Computing Devices, Inc. XRemote feature on all terminal servers and protocol translators. When fonts used by X applications are not included in ROM on the NCD terminal, one or more font servers must be identified from which the protocol translator and the NCD terminal can obtain non-ROM fonts. Answer "yes" to specify one or more XRemote font servers. Refer to the chapter, "Configuring XRemote", for details about specific XRemote parameters.
Answer "no" if you do not want to specify XRemote font servers.
Default: Yes
Font servers must be reachable and IP-addressable entities. In order to obtain fonts from a specific host (or hosts), you must enter the IP address(es).
Enter the Internet address of the font server in dotted decimal form (for example. 131.108.2.5). If you do not know the Internet address, consult your network manager.
This step is equivalent to specifying the IP address of a font server when using the xremote tftp host global configuration command. However, a host name cannot be entered when setup is running, since the name service facility is not yet available. Refer to the chapter, "Configuring XRemote," for more details about XRemote configuration options.
Respond to the prompt by pressing Return to stop entering font server IP addresses.
Default: None
Help: Enter an Internet address of the form "X.X.X.X", where each letter corresponds to a decimal number between 0 and 255.
The following interface configuration activities are handled via the setup command:
Each interface configuration step in the setup process is described sequentially in the descriptions that follow.
The setup command facility automatically presents the installed interface for you to configure.
Internet addresses are 32-bit quantities assigned to hosts that use the TCP/IP protocols. These addresses are usually written as four decimal numbers separated by periods (for example, 192.17.5.100). Each number is an eight-bit value between 0 and 255.
The addresses are divided into three classes; the classes differ in the number of bits allocated to the network and host portions of the address.
The Class A Internet address format allocates the highest eight bits to the network field and sets the highest-order bit to 0 (zero). The remaining 24 bits form the host field.
The Class B Internet address allocates the highest 16 bits to the network field and sets the two highest-order bits to 1, 0. The remaining 16 bits form the host field.
The Class C Internet address allocates the highest 24 bits to the network field and sets the three highest-order bits to 1,1,0. The remaining eight bits form the host field.
Enter your Internet address in dotted decimal form (for example, 131.108.2.5). If you do not know your Internet address, consult your network manager.
Network First Network Host
Class Byte Bits Bits
A 1-126 8 24
B 128-191 16 16
C 192-223 24 8
Default: None
Help: Enter an Internet address of the form "X.X.X.X," where each letter corresponds to a decimal number between 0 and 255.
Subnetting is an extension of the Internet addressing scheme, which allows multiple, physical networks to exist within a single Class A, B, or C network. The usual practice is to use a few of the leftmost bits in the host portion of the network address for a subnet field. The subnet mask controls whether or not subnetting is in effect on a network.
Internet addressing conventions allow either 24, 16, or 8 bits for a subnet mask, depending on whether your address is Class A, B, or C, respectively. However, because the last two of these bits are used for the host address, the setup command facility allows you to specify up to 22, 14, or 6 bits for your subnet mask.
A caveat applies to all classes of addresses: users may not specify "1" as a number of bits for the subnet mask. Such a specification would provide either an all zeros or all ones subnet mask, both of which are reserved by Internet conventions.
Default: 0
Help: A decimal number between 0 and 22, 14, or 6, depending on whether your network is Class A, B, or C, respectively.
LAT is by default enabled on any network interface for a CPT. Refer to the chapter, "Configuring LAT," for details about specific LAT parameters. Enter "yes" to enable LAT (or simply press Return).
Answer "no" if you do not want to enable LAT.
Default: Yes
By default, the Cisco protocol translators support DEC's Maintenance Operation Protocol (MOP), which allows remote access from DEC computers for maintenance purposes. By responding with a "yes" or pressing the Return key, MOP is enabled for the interface. Refer to the chapter "Using the DEC MOP Server" in this manual for details about Cisco's support of the DEC MOP capabilities and related interface configuration commands.
Answer "no" if you want to completely disable DEC MOP on the interface.
Default: Yes
Using the setup command, you can think of the configuration process as a "loop." For example, at this point, you have now completed configuring Ethernet0. Next, the system will automatically continue to present the next interface for configuration (either Ethernet1 or Serial0 for a protocol translator), until both interfaces have been configured.
Default: Yes
The system requires that you provide an answer. Answering "yes" stores the configuration in non-volatile memory. Answer "no" and the configuration is not saved. This marks the end of the configuration process.
Default: None
You are now ready to try using the other commands available to you, including the show and configure commands. To make changes to the configuration using the setup command facility, type setup at the EXEC prompt. Refer to the chapter, "Configuring the System," and protocol-specific chapters of this manual for advanced configuration.
The following is a sample of a complete CPT setup session, including the prompts provided after setup has terminated.
Would you like to enter the initial configuration dialog? [yes]: Enter host name [CPT]:gate-1 Enter enable password:nojoy Enter virtual terminal password:fooluser Configure SNMP Network Management? [yes]: Configure Xremote font servers? [yes]:no Configuring interface Ethernet0: IP address for this interface:131.108.161.10 Number of bits in subnet field [0]:8 Class B network is 131.108.0.0, 8 subnet bits; mask is 255.255.255.0 Configure LAT on this interface? [yes]: Configure MOP on this interface? [yes]: Configuring interface Serial0: IP address for this interface:131.108.161.50 Number of bits in subnet field [0]:8 Class B network is 131.108.0.0, 8 subnet bits; mask is 255.255.255.0 Configure LAT on this interface? [yes]: The following configuration command script was created: hostname gate-1 enable password nojoy line vty 0 9 password fooluser snmp-server community ! ! interface Ethernet0 ip address 131.108.161.28 255.255.255.0 lat enabled mop enabled ! interface Serial0 ip address 131.108.161.60 255.255.255.0 lat enabled end Use this configuration? [yes/no]:yes Press RETURN to get started! [OK] Use the enabled mode 'configure' command to modify this configuration. gate-1>
|
|