cc/td/doc/product/software/ios11
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

SNA Frame Relay Access Support Commands

SNA Frame Relay Access Support Commands

This chapter describes the commands to configure System Network Architecture (SNA) Frame Relay access support. For SNA Frame Relay access support configuration tasks and examples, refer to the "Configuring SNA Frame Relay Access Support" chapter of the Router Products Configuration Guide.


Note Because Frame Relay itself does not provide a reliable transport as required by SNA, the RFC 1490 support of SNA uses LLC2 as part of the encapsulation to provide link-level sequencing, acknowledgment, and flow control. The serial interface configured for IETF encapsulation (RFC 1490) accepts all LLC2 interface configuration commands. For more information about LLC2 interface configuration commands, refer to the "LLC2 and SDLC Commands" chapter of the Router Products Command Reference publication.

fras map llc

Use the fras map llc interface configuration command to associate an LLC connection with a Frame Relay connection. Use the no form of this command to cancel the association.

fras map llc mac-address lan-lsap lan-rsap serial port frame-relay dlci fr-lsap fr-rsap
[PFID2 | AFID2 | FID4]
no fras map llc
mac-address lan-lsap lan-rsap serial port frame-relay dlci fr-lsap
fr-rsap
[PFID2 | AFID2 | FID4]
Syntax Description
mac-address The MAC address of the downstream SNA device. It is a 48-bit dotted-triple address.
lan-lsap The local SAP address of the downstream SNA device in hexadecimal. For SNA, the address must be multiples of 4.
lan-rsap The destination SAP address from the perspective of the downstream SNA device in hexadecimal. For SNA, the address must be multiples of 4.
serial port The serial interface on which Frame Relay is configured.
frame-relay dlci The Frame Relay data link connection identifier.
fr-lsap The local SAP address of the logical link connection on the CFRAD.
fr-rsap The destination SAP address on the host.
PFID2 (Optional) The FID2 SNA transmission header for SNA peripheral traffic.
AFID2 (Optional) The FID2 transmission header for APPN traffic.
FID4 (Optional) The transmission header used on SNA subarea flows.
Default

No defaults are defined.

Command Mode

Interface configuration

Usage Guidelines

You can map multiple LLC sessions to a DLCI.

Example

The following example associates an LLC connection to a Frame Relay connection:

fras map llc 0800.5a8f.8802 4 4 serial 0 frame-relay 200 4 4
Related Command

frame-relay map llc2

fras map sdlc

Use the fras map sdlc interface configuration command to associate an SDLC link with a Frame Relay DLCI. Use the no form of this command to cancel the association.

fras map sdlc sdlc-address serial port frame-relay dlci fr-lsap fr-rsap [PFID2 |
AFID2
| FID4]
no fras map sdlc sdlc-address serial port frame-relay dlci fr-lsap fr-rsap [PFID2 |
AFID2 | FID4]
Syntax Description
sdlc-address The SDLC address of the downstream SNA device in hexadecimal.
serial port The serial interface on which Frame Relay is configured.
frame-relay dlci The Frame Relay data link connection identifier.
fr-lsap The local SAP address of the logical link connection on the CFRAD.
fr-rsap The destination SAP address on the host.
PFID (Optional) The FID2 SNA transmission header for SNA peripheral traffic.
AFID2 (Optional) The FID2 transmission header for APPN traffic.
FID4 (Optional) The transmission header used on SNA subarea flows.
Default

No defaults are defined.

Command Mode

Interface configuration

Usage Guidelines

You can map multiple SDLC links to a DLCI.

Example

The following example associates an SDLC link with a Frame Relay DLCI:

fras map sdlc C1 serial 0 frame-relay 200 4 4
Related Command

frame-relay map llc2

frame-relay map llc2

Use the frame-relay map llc2 interface configuration command to map LLC2 traffic to a DLCI.

frame-relay map llc2 dlci-number
Syntax Description
dlci-number The Frame Relay data link connection identifier.
Default

No defaults are defined.

Command Mode

Interface configuration

Example

The following example maps LLC2 traffic to DLCI number 200:

frame-relay map llc2 200

frame-relay map rsrb

Use the frame-relay map rsrb interface configuration command to specify the DLCI number onto which the RSRB traffic is to be mapped.

frame-relay map rsrb dlci-number
Syntax Description
dlci-number The Frame Relay data link connection identifier.
Default

No defaults are defined.

Command Mode

Interface configuration

Example

The following example shows RSRB traffic mapped to DLCI number 30:

frame-relay map rsrb 30
Related Command

encapsulation frame-relay

llc2 dynwind

Use the llc2 dynwind interface configuration command to enable dynamic window congestion management. Use the no form of this command to cancel the configuration.

llc2 dynwind [nw nw-number] [dwc dwc-number]
no llc2 dynwind
[nw nw-number] [dwc dwc-number]
Syntax Description
nw nw-number (Optional) Specifies a number of frames that must be received to increment the working window value by 1.
dwc dwc-number (Optional) Specifies the number by which the working window value is divided when BECN occurs. Valid numbers are 1, 2, 4, 8, and 16. 1 is a special value that indicates that the working window value should be set to 1 when BECN is indicated
Default

The default nw-number value is 4 frames.

The default dwc-number value is 1.

Command Mode

Interface configuration

Example

The following example specifies that to increment the working window 6 frames must be received, and that when BECN is indicated the working window value should be set to 1:

llc2 dynwind nw 6 dwc 1

show fras map

Use the show fras map privileged EXEC command to display the mapping and connection state of Frame Relay access support.

show fras map
Syntax Description

This command has no arguments or keywords.

Command Mode

Privileged EXEC

Sample Display

The following is sample output from the show fras map command:

Router# show fras map
Type Destination    Int   LSap   RSap   Role   State
tr   0800.5a8f.8802 tr0   4      4      P      ls_contacted
fr   200            s0    4      4      S      ls_contacted

Table 31-1 describes significant fields shown in the display.


Table  31-1: Show FRAS Map Field Descriptions
Field Description
Type Interface type.
Destination Destination address.
Int Interface.
LSap Local SAP.
RSap Remote SAP.
Role Local link station role; P means Primary, S means Secondary.
State Link station protocol machine state.

hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1997 © Cisco Systems Inc.